What to do if Your Sink Stopper is Stuck

There are times when the sink stopper can become stuck. This can be frustrating, and it may even prevent you from using your sink. This can cause a big problem, especially if you need to use the sink for cooking or cleaning. The blockage can make your sink start to smell, and it can also cause your pipes to back up. You need to be able to fix the problem as soon as possible. Luckily, removing a stuck sink stopper is not as difficult as it may seem. With a little bit of patience and the right tools, you should be able to fix the problem in no time. There are a few things that you can do if your sink stopper is stuck. They are the best methods and they will help you in fixing the problem as soon as possible. The following are some of the things that you need to do:

1. Pull With Magnet

You should try to pull the stopper with a magnet. This will help you in getting a grip on the object and it will also help you in pulling it out. The process is simple and you will not have to worry about anything. You should just make sure that you have a good grip on the object. After you have a good grip on the object, you should try to pull it out. If you cannot pull it out, you should try to push it back in. This will help you in getting a better grip on the object. You should try to use a plunger if you cannot pull the object out with a magnet. This will help you in getting a better grip on the object and it will also help you push it back in.

2. Use A Flathead Screwdriver

If you cannot pull the stopper out with a magnet, then you should try to use a flathead screwdriver. First, you need to find the set screw that is holding the stopper in place. The setscrew is usually located on the underside of the stopper. Once you have found the set screw, you should use the flathead screwdriver to loosen it. After the set screw is loosened, you should be able to pull the stopper out of the drain. When using a flathead screwdriver, you need to be very careful not to damage the drain. If you damage the drain, you may need to replace it. So, you need to be very careful when using a flathead screwdriver.

3. Use A Plunger

The plunger is a household essential that can be used for various purposes, one of them being unclogging a sink. To use a plunger to fix a stuck sink stopper, fill the sink with enough water to cover the plunger’s cup. Next, place the plunger over the drain and make sure there’s a good seal. Finally, start plunging up and down vigorously until the stopper is released.

4. Use A Pair Of Pliers

If the stopper is still stuck, you may need to use a pair of pliers to remove it. You should be able to get a grip on the stopper with the pliers and then twist it counterclockwise to remove it. According to Home guides, The process may take a few tries, but eventually, you should be able to get the stopper out. You need to be very careful when using pliers so that you don’t damage the finish on your sink. If you’re worried about scratching the surface, you can wrap the jaws of the pliers with a piece of cloth before you begin.

5. Pop-Up Stopper Parts

This is the easiest way to remove a stuck sink stopper, but it only works if your sink is equipped with pop-up stopper parts. All you need to do is locate the knob or lever that controls the pop-up stopper. In most cases, this will be located underneath the sink. Once you’ve found the knob or lever, simply push it down to release the stopper. The stopper should pop up and be easily removed. According to Thespruce, If your sink is not equipped with pop-up stopper parts, you’ll need to use one of the other methods described below;

• Pop-Up Stopper: The pop-up stopper is the part of the sink that pops up and down to open and close the drain.
• Lift Rod: The lift rod is what you use to operate the pop-up stopper. It’s usually attached to the stopper itself, but in some cases, it may be located on the side of the sink.
• Lift Rod Strap: The lift rod strap is what holds the lift rod in place. It’s usually made of metal and is attached to the underside of the sink.
• Horizontal Rod: The horizontal rod is what the lift rod attaches to. In most cases, it will be located on the back of the sink.
• Clip: The clip is what holds the horizontal rod in place. It’s usually made of metal and is located on the underside of the sink.

6. Fix Stuck Sink Stopper

The final step is to fix the sink stopper so it doesn’t become stuck again. There are two ways to do this. The first is to adjust the tension on the stopper. This can be done by loosening or tightening the screw that holds the stopper in place. According to Community, The second way to fix a stuck sink stopper is to replace the entire unit. This is a more permanent solution, but it will require you to purchase a new stopper. Once you have fixed the problem, be sure to test the stopper regularly to make sure it is working properly. This will help you avoid future problems and keep your sink stopper working properly for years to come.

Conclusion

When it comes to a stuck sink stopper, there are a few different things that you can do to fix the problem. In most cases, all you will need to do is adjust the tension on the stopper or replace the entire unit. Be sure to test the stopper periodically to ensure that it is working properly. You don’t want to wait until it becomes stuck again to try and fix the problem. With a little bit of care, you should be able to keep your sink stopper working properly for years to come.

You can also read:

• Here’s a Quick Bathroom Sink Size Guide
• The Five Best Bathroom Sink Strainers Money Can Buy
• Can You Drain a Sink into a Toilet Vent?